Material Info
My Products are being supplied by ABC Supply Co.inc (www.abcsupply.com) .  Below is the information of the material/product I use :

COMMONWEALTH ALUMINUM CORPORATION CONTINUOUS RAINWARE ALUMINUM COIL FOR USE AS RAIN CARRYING EQUIPMENT LIMITED TWENTY (20) YEAR WARRANTY

The manufacture, Commonwealth Aluminum Corporation warrants that the finish on your Commonwealth Aluminum continuous aluminum gutter will not blister, peel, crack, chip, flake, check, or split for a twenty (20) year period from the date of installation if, on proper invocation by the manufacture, or its appointed depreciative, it is disclosed that the finish has blistered, peeled, cracked, chipped, flaked, checked or split within said twenty (20) year period, the manufacture will be responsible for cost of refinishing or repairing defective material or where applicable, a refund on the following pro-raced basis, 100% during the first year, 100% of the cost of cleaning refinishing, or replacing for the first year of the warranty  period. For each succeeding year of the warranty, CAC’s obligation shall be reduced by 5% of the cost such that by the twentieth (20th) year CAC shall assume only 5% of the total cost to clean, refinish, or replace a defective Product.

Refinishing or replacement of defective material is at the option of the manufacture.  The bias for determining cost recoverable under this warranty is as follows: refinishing the current prevailing area finishing cost replacement of the-the price of Commonwealth continuous aluminum coil at the time of settlement or the original price of the material, all at the sole discretion of Commonwealth Aluminum Corporation.  This warranty covers the material only.  The manufacture is no way responsible for forming, stamping, or installation, which is the responsibility of the distributor, dealer contractor, or applicator.

This warranty does not cover damage or deterioration caused by faulty installation, collation with foreign objects, hail, ice, lighting, earthquakes, erosion, explosions, external forces, normal weathering, riots, vandalism, civil commotion’s misuse, or other occurrtences beyond the control of the manufacture.

This warranty applies only to the finish applied on continuous coil material and accessories manufactured and sold by Commonwealth Aluminum Corporation.  Finishes applied by anyone other than Commonwealth Aluminum Corporation are excluded from this warranty.

ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR USE ARE LIMITED IN DONATION TO TEN (10) YEARS, SELLERS MAKE NO WARRANTY, EXPRESS OR IMPLIED OTHER THAN SET FORTH HERE, OR REQUIRED BY LAW.

Liability of the manufacture is limited to the purchase price.  SELLER SHALL IN NO LIABLE FOR INCIDENT OR CONSEQUENTIAL DAMAGES ANY KIND WHATSOEVER WHETHER ALLEGED TO HAVE RESULTED FROM DELAY IN DELIVER, DELIVERY OF NON-CONFORMING MATERIAL, DEFICIENCIES IN MATERIAL, OR ANY OTHER CAUSE WHATSOEVER, AND WHETHER ARISING FROM BREACH OF CONTRACT, BREACH OF WARRANTY, TORY, INCLUDING, NEGLIGENCE, STRICT LIABILITY OR OTHERWISE.  The ready set for above shall be exclusive.

Some states do not allow limitations on how long an implied warranty lasts.  Or the exclusive or limitation of consequential damages, so the above limitations or exclusions may not appeal to you.

This warranty gives you specific legal rights and may also have other rights which vary, from state to state.

All claims under this warranty must be made in writing within thirty (30) days after appearance or any defect.  This warranty is not effective unless signed and dated by the installing dealer at time of installation.  This warranty extends to the original purchaser only and cannot be assigned or otherwise transferred.

GUTTER COIL SPECIFICATIONS SHEET
COMMONWEALTH ALUMINUM
NEWPORT ROLLING MILL

Products
3105 H24 .027” x 11.75”
3105 H24 .032” x 15.00”

Physical Data
Physical Form : SOLID
Boiling Point : N/A
Melting Point : 900.1200 F
Vapor Pressure : N/A
Density : 2.63-3.12 g/cc

Chemical Composition Limits – 3105 Alloy

MECHANICAL PROPERTIES LIMITS

CHEMICAL COMPOSITION

MECHANICAL PROPERTIES (minimum or range)

RECOMMENDED RADIAL FOR 90 degree BENDS (Aluminum Association)
Expressed in Terms of T-Thickness

Temper            .016”                .032”                .088”                .128”

H22                 0                      0                      0                      1/2T

H24                 0                      0                      1/2T                 1T

H26                 1/2T                 1/2T                 1/2T                 1T

H28                 1/2T                 1T                    1-1/2T             2T

CII ALUMINUM ALLOY
MATERIAL SAFETY DATA SHEET

Section I Material Description

• Date : 11-4-85, Revision Date : 8-1-00

• Manufacturer : Commonwealth Aluminum Corporation

• PO Box 480

• Lewisport, Kentucky 42351

• Trade Name : Aluminum Coil, Flat Sheet or Plate

• Product Class : Aluminum Alloy

• Identification :

• Manufacturers Code : 1100, 1145, 1350, 3003, 3004, 3104, 3105, 3204, 3304, 7021, 7072, 8111, and 131122

Section II Ingredients

• Aluminum            >92.10             7429-9-5       5                      10

• Magnesium          <2.05               7439-95-4     10

• Zine                     <5.85               7440-66-6     5

• Manganese          <1.50               7439-96-5     5 (coiling)         5 (coiling)

Section III Physical Data

• Melting Range : 950-1150 degree F

• Vapor Density : Unknown

• Evaporating Rate : Unknown

• Percent Volatile By Volume : Unknown

• Appearance and Odor : Dull or Silver Metallic Color, no odor.

Section IV Fire and Explosion Hazard Data

• Flash Point : Unknown

• LEL : Unknown

• Extinguishing Media : Use extinguishing agent appropriate for combustible materials in area.  Dry chemical recommended.

• Unusual Fire and Explosion Hazards: Molten Aluminum in the presence of water, is very unstable.  Do not use water to extinguish where there is a possibility of molten aluminum being present.  Finely divided aluminum will form explosive mixtures in air.

Section V Health Hazard Data

• Effects of Overexposure : High Exposures may produce irritation of the eyes and respiratory tract.  It exposures for aluminum oxide are kept below the TLV’s the alloy components should not present any helth risk.  Welding or cutting aluminum may generate ozone.  Overexposure to ozone can cause mucous membrane irritation and pulmonary changes including irritation, congestion and edems.

• Emergency and First Aid Procedures : Eye Contact : wash eyes with large volumes of water for 15 minutes.  If irritation persists seek medical attention.  Skin contact : wash with soap and water.  Inhalation : remove to fresh air and initiate appropriate repiratory support.  Consult a physician.  Ingestion : extremely unlikely.

• Carcinogenicity : This material is not considered to be carcinogenic as currently listed by the NTP, IARC, or OSHA.

Section VI Reactivity Data

• Stability : Stable

• Hazardous Polymerization : Will not occur

• Conditions to avoid : See Section IX

• Hazardous Decomposition Products : None

Section VII Spill or Leak Procedures

• STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: No special procedure.

• WASTE DISPOSAL METHOD: For disposal of this material as a waste, act in accordance with all applicable federal, state and local waste management regulations.  Recycling of aluminum is incommode by the industry.

Section VIII Special Protection Information

• RESPIRATORY PROTECTION: If  TLV’s exceeded use NOSH approved dust or fume respirator depending on continents and concentrations present.

• VENTILATION: Local exhausts if TIV’s exceeded.

• PROTECTIVE Gloves: Recommended while handing abet or coil.

• EYE PROTECTIVE EQUIPMENT: Eye gasses or goggles depending on prevailing hazard.

• OTHER PROTECTIVE EQUIPMENT: None.

Section IX Special Precautions

• PRECAUTIONS TO BE TAKEN IN HANDING AND STORING: None under normal conditions of use and storage.

• OTHER PRECAUTIONS: Halogen acids and sodium hydroxide in contract with aluminum may generate explosive mixtures of hydrogen.

• Do not touch cast aluminum metal or heated aluminum product without knowing metal temperature.  Aluminum experience no color change during heating if metal is hot and touched, burns can result.

• The welding  of aluminum alloys may generate carbon monoxide, ozone, nitrogen oxides, infrared radiation and ultra-violet radiation.

Information herein is given in good faith as authoritative and valid: however, no warranty, express or implied, can be made.  The conditions or methods of handing storage, use and disposal of the product are beyond our control and may be beyond our knowledge.  For this and other reasons, we do not assume responsibility and expressly liability for loss, damage or expense arising out of in any way connected with the handling, storage, use or disposal of the material.